FLUKE 8505A PDF

Fluke A Digital Multimeter DIGIT Engineering Bench Precision OPT 02a 03 About this product. About this product. Product Identifiers. BRAND. Fluke. Full text of “FLUKE A Instruction”. See other formats. Instruction Manual P/N MARCH 1 REV 1, 3/86 ®, John Fluke Mfg. Co., Inc. All Rights. Active Filter Block Diagram A Fast A/D Converter The Fast A/ D Converter employs Fluke’s patented recirculating remainder (R2) technique.

Author: Nikogis Mikaramar
Country: Portugal
Language: English (Spanish)
Genre: Politics
Published (Last): 4 February 2009
Pages: 44
PDF File Size: 15.73 Mb
ePub File Size: 9.12 Mb
ISBN: 452-1-21084-946-7
Downloads: 64115
Price: Free* [*Free Regsitration Required]
Uploader: Yozshuramar

Considerable versatility is realized through unique contruction. Error System error, usually appears at power-up or reset.

Showing Results for Fluke 8505A

If no flhke standard error response message has been programmed sincethe last power-up or reset, a “2” is returned to identify an error occurring during limits testing.

Ohms input problem Error 27 can occur under any of the following circumstances: Characters in excess of 15 are ignored by the multimeter and do not cause an error condition.

However, the zero value is stored in the following new fashion: The sync signal thereby allows for faster bus communications by advancing a scanner before a new reading is triggered. The temporary zero values are reset to 0 when the multimeter is powered-up or reset.

May be wired internally for either rising or falling edge. Response is as follows: DC Current Any subsequent activation of External Reference mode replaces the software number with the actual external reference value.

Ohms input problem Error 27 can occur under any of the following circumstances: Complete descriptions and instructions are included for the instrument mainframe, for all flukw necessary in making dc volts measurements, and for any optional modules ordered with the instrument.

  LH FLUGPLAN PDF

The function is changed.

Fluke A Digital Multimeter DIGIT Engineering Bench Precision OPT 02a 03 05 | eBay

Analog Signal Flow Each module is addressed by the controller as virtual memory. Also, error 24 may mean that the wrong ac flukr configuration is installed. The 24 bits of the next 3 bytes serve as the binary fraction. Select the desired function. Complete software calibration information is presented in Section 7 of this manual.

Fluke 8505A reference multimeter

The following rules apply: Use the following sequence: Each of these changes resembles that detailed above for the A, with the following exceptions: Examples of such operations are given under Applications later in this section. Synchronous or asynchronous operation can be specified remotely. Greater than or equal to dB with less than 4 samples per reading. If flukw multiple error condition exists, only the flukke error to have been generated Is stored in the error buffer.

Front Panel Push Buttons cont A Mathematic Operations; To store the displayed value as an offset orscaling flukke and enter the respective mode: Further programming from the front panel is often not necessary. Microprocessor Control If it is necessary to clear all calibration factors as in a check sum error 25 condition or prior to hardware calibration of all functionsthe K4G1 command string can be used.

The status information controls and synchronized the activities of the external logic. The read value may not be stored as a Scaling Factor.

  LOIC WACQUANT ENTRE LAS CUERDAS PDF

A second store sequence must be used if both high and low limits are desired. Characters in excess of 15 are ignored by the multimeter and do not cause an error condition. This warranty extends only to the original purchaser. Basic operations of the each digit. This number may signify the calibration date. DC External Reference Test The first step involves a user- programmed error message that is returned whenever an error condition has been generated.

Remote control can only be commanded from the remote location with this interface. The display is multiplexed by minimized by software design.

Fluke A Digital Multimeter, OPT 02A, 03, 09A – NOTE: FUNCTIONAL FOR DC & OHMS ONLY

Any immediate character including termination characters terminates and executes the string normally. Resolution 2- 6. Any previously selected output format is restored once High Speed mode is exited.

Since these higher sample settings may require considerable time for a display update, this f,uke is necessary to insure that the operator is aware of a reading in progress. Speed of measurement is not important.

Programming Instructions cont An example of an illegal numeric string is; 0 N J 0QO0 Exponent is limited to one signed integer digit, in this case the exponent would be -1 and the “3” would be ignored.

Therefore, the actual reading is returned, and the error buffer is reset to